IMPLEMENTATION OF 3D PRINTING TECHNOLOGY TO SUPPORT INNOVATIVE AND CREATIVE LEARNING FOR STUDENTS AND TEACHERS OF SMAN 1 SIDAYU GRESIK

Isi Artikel Utama

Dyah Hikmawati
Aminatun Aminatun
Aniek Setiya Budiatin
Herri Trilaksana

Abstrak

Background. Integrating three-dimensional (3D) printing technology into secondary education offers opportunities to enhance digital literacy, experiential learning, and innovative teaching practices. However, limited access to digital fabrication equipment and insufficient technical competencies among teachers and students remain challenges to its implementation.


Aims. This community service program aimed to introduce 3D printing technology, strengthen participants’ understanding of digital fabrication, and promote its potential application in creative and project-based learning at SMAN 1 Sidayu, Gresik, Indonesia.


Methods. The program employed a participatory, practice-oriented approach comprising four stages: preparation, implementation, evaluation, and sustainability support. Activities included interactive lectures, technology demonstrations, guided 3D modeling exercises, and practical instruction in preparing digital designs for printing. Program outcomes were evaluated using pre-test and post-test assessments involving 35 participants and a satisfaction questionnaire completed by 31 respondents. Result. The findings revealed an increase in mean knowledge scores from 48.63 to 54.71, representing a gain of approximately 6.08 points. Individual performance improved for 54.3% of participants, remained unchanged for 31.4%, and declined for 14.3%. Furthermore, 93.5% of respondents rated the overall program as Very Good, while facilities and instructional quality received Very Good ratings of 91.6% and 89.5%, respectively. Participants nevertheless identified the need for longer practical sessions, more opportunities for independent printing, and improved instructional pacing. A 3D printer was donated to the school to support ongoing technology-based learning activities.


Conclusion. These findings suggest that structured training combined with equipment provision can support initial technological understanding and create opportunities for integrating digital fabrication into secondary education. However, sustained mentoring, teacher capacity development, and longitudinal evaluation are necessary to establish the program’s long-term educational impact.

Rincian Artikel

Cara Mengutip
Hikmawati, D., Aminatun , A., Aniek Setiya Budiatin, & Herri Trilaksana. (2026). IMPLEMENTATION OF 3D PRINTING TECHNOLOGY TO SUPPORT INNOVATIVE AND CREATIVE LEARNING FOR STUDENTS AND TEACHERS OF SMAN 1 SIDAYU GRESIK. Jurnal Abdisci, 4(1), 1–16. https://doi.org/10.62885/abdisci.v4i1.1372
Bagian
Articles

Referensi

Ford, S., & Minshall, T. (2019). Invited review article: Where and how 3D printing is used in teaching and education. Additive Manufacturing, 25, 131–150. https://doi.org/10.1016/j.addma.2018.10.028

Global Education Monitoring Report Team. (2023). Global education monitoring report 2023: Technology in education: A tool on whose terms? UNESCO. https://doi.org/10.54676/UZQV8501

Greenhalgh, S. (2016). The effects of 3D printing in design thinking and design education. Journal of Engineering, Design and Technology, 14(4), 752–769. https://doi.org/10.1108/JEDT-02-2014-0005

Harron, J. R., Emert, R., Thomas, D. M., & Campana, J. (2022). Laying the groundwork for STEAM: Scaling and supporting 3D design and printing in higher education. Frontiers in Education, 6, 763362. https://doi.org/10.3389/feduc.2021.763362

Huang, C.-Y., & Wang, J.-C. (2022). Effectiveness of a three-dimensional-printing curriculum: Developing and evaluating an elementary school design-oriented model course. Computers & Education. https://doi.org/10.1016/j.compedu.2022.104553

Li, J. F., & Glassford, E. K. (2025). Three-dimensional (3D) printing in non-industrial spaces: A summary of emissions evaluations in 11 school settings. Journal of School Health, 95(4–5), 307–316. https://doi.org/10.1111/josh.13541

Lin, K.-Y., Lu, S.-C., Hsiao, H.-H., Kao, C.-P., & Williams, P. J. (2023). Developing student imagination and career interest through a STEM project using 3D printing with repetitive modeling. Interactive Learning Environments, 31(5), 2884–2898. https://doi.org/10.1080/10494820.2021.1913607

Novak, E., Brannon, M., Librea-Carden, M. R., & Haas, A. L. (2021). A systematic review of empirical research on learning with 3D printing technology. Journal of Computer Assisted Learning, 37(5), 1455–1478. https://doi.org/10.1111/jcal.12585

Özeren, Ö., Özeren, E. B., Top, S. M., & Qurraie, B. S. (2023). Learning-by-doing using 3D printers: Digital fabrication studio experience in architectural education. Journal of Engineering Research, 11(3), 100135. https://doi.org/10.1016/j.jer.2023.100135

Salazar, D., Thompson, M., Rosen, A., & Zuniga, J. (2022). Using 3D printing to improve student education of complex anatomy: A systematic review and meta-analysis. Medical Science Educator, 32(5), 1209–1218. https://doi.org/10.1007/s40670-022-01595-w

Stefaniak, A. B., et al. (2021). Use of 3-dimensional printers in educational settings: The need for awareness of the effects of printer-generated emissions. [Full bibliographic details retained in the source manuscript].

Stern, A., Rosenthal, Y., Dresler, N., & Ashkenazi, D. (2019). Additive manufacturing: An education strategy for engineering students. Additive Manufacturing, 27, 503–514. https://doi.org/10.1016/j.addma.2019.04.001

Tejera, M., Galiç, S., & Lavicza, Z. (2025). 3D modelling and printing in teacher education: A systematic literature review. Journal for STEM Education Research. https://doi.org/10.1007/s41979-025-00147-2